•soldering

soldering 发音

英：[ˈsɑːdərɪŋ]　　美：[ˈsəʊldərɪŋ]

英：　　美：

soldering 中文意思翻译

soldering 词性/词形变化，soldering变形

动词过去分词: soldered |动词现在分词: soldering |名词: solderer |动词第三人称单数: solders |动词过去式: soldered |

soldering 短语词组

1、soldering flux paste ─── [医] 焊媒膏

2、soldering paste ─── [化] 钎焊膏; 钎焊剂

3、soldering iron ─── 烙铁 [电] 焊铁

4、solder reflow soldering ─── [计] 回流锡焊

5、soldering pliers ─── [医] 焊钳

6、soldering flux ─── [化] 焊剂 ─── [医] 焊媒

7、autogenous soldering ─── [化] 自焊 ─── [医] 自生焊接

8、soft-soldering ─── 软钎焊； ─── 软焊；锡焊

9、fusing soldering ─── [化] 熔焊

10、flow soldering ─── [电] 流动焊接

11、dip-soldering ─── [计] 浸焊

12、band soldering pliers ─── [医] 焊圈钳

13、iron soldering ─── [化] 烙铁钎焊

14、electric soldering iron ─── [机] 电烙铁

15、soldering clamp ─── [医] 焊夹

16、electric soldering ─── [电] 电焊

17、silver soldering ─── [机] 银硬焊

18、soldering agent ─── [化] 焊剂

19、soldering investment ─── [医] 焊接围模法, 焊接围模料

soldering 常用词组

wave soldering ─── 波峰焊接；波峰焊接技术

reflow soldering ─── 再流焊；回流焊接

soldering tin ─── n. 焊锡；焊锡条

soldering 相似词语短语

1、moldering ─── v.腐朽；崩坏；使腐朽（molder的现在分词）

2、soldiering ─── n.当兵；军旅生活；v.从军；坚持；装病（soldier的现在分词）

3、shouldering ─── n.碰撞驱舰，撞舰驱赶；肩托

4、smoldering ─── n.闷烧，阴燃；adj.(情绪)郁积的（smoder的变形）

5、smouldering ─── adj.缓慢燃烧的；流露难以压抑情感的；v.阴燃，闷燃；（感情）郁积，压抑；流露难以抑制的感情（smoulder的现在分词）

6、unsoldering ─── v.拆焊（unsolder的现在分词）

7、solderings ─── v.焊接，焊合；（使）结合（solder的现在分词）；n.紧扣

8、resoldering ─── 分辨率

9、bouldering ─── n.抱石运动；用大鹅卵石铺的路；v.使成巨砾（boulder的ing形式）

soldering 常见例句（双语使用场景）

1、Install exhaust pipe at soldering area. ─── 安装排气管于焊接区。

2、Low voltage 24V thermostat soldering pen protects the faulty circuit board. ─── 低压恒温24V烙铁有效保护维修线路板。

3、As the solder melts, it will "wick" into the copper braid. ─── 当焊料熔化时，就会“吸入”铜编织带中。

4、Solder end valves also available. ─── 也可以提供焊接连接端口的阀门。

5、Stir solder paste in container before use. ─── 使用时搅拌容器内的焊膏。

6、Analyze common bad soldering question in wave soldering and put forward the solution countermeasrue. ─── 对波峰焊常见的焊接不良问题给予分析并提出解决对策。

7、The ground solder for the Vrs. ─── 地面焊料的越南难民。

8、Quality problem and solution on lead-free solder was reviewed. ─── 并对无铅焊接特有的质量问题及解决方法进行了评述。

9、If I'm going to teach my daughter about electronics, I'm not going to give her a soldering iron. ─── 如果我准备教我女儿电子学，我不会给她一个烙铁。

10、Antistatic 24V soldering iron has good protection of PCB. ─── 低压24V烙铁为防静电设计,有效保护线路板。

11、He was even able to get soldering using a almost handmade device connected to a concrete mixer, trying to adapt the said part. ─── 他能够得到利用，甚至几乎是手工焊接设备连接到一个混凝土搅拌机，努力适应输出的一部分。

12、Care must be taken not to overheat and damage valves during the soldering process. ─── 在焊接过程中，必须要小心谨慎，避免由于温度过高导致阀门受到损害。

13、If the connection is to be made by soldering, turn the handwheel to the fully open position before applying heat. ─── 如果是焊接连接,则在加热之前要把手轮旋转到全开的位置。

14、All-in-one complex tip design (70W heater, sensORtip) has strong heat recovery fORleadfree soldering. ─── 一体化复合咀设计(70W发热芯,感温焊咀)有强大回热功能,适用于无铅焊接.

15、Peak soldering reflow temperature also impacts cleaning performance. ─── 再流焊的峰值温度也会对清洗性能造成影响。

16、Technical school or above 12 to 24 months soldering experience, comprehensive knowledge of soldering quality. ─── 中技或中技以上学历。12至24个月锡焊工作经验，熟悉锡焊材料和焊点品质要求。

17、Thank you for using SMIC Solder Recovery System! ─── 感谢您购买斯迈克锡渣还原机产品！

18、Make it into a pair by soldering the cutten foot. ─── 将短脚焊接在一起成为一个双头的2极灯管。

19、With more than 100 years experience in soldering technologies, Kester understands the challenges of lead-free wave soldering. ─── 凯斯特公司具有100多年从事焊接技术的经验,了解无铅焊接带来的各种挑战。

20、SMOBC: Solder mask over bare copper. ─── 一种阻焊层覆盖裸铜的工艺。

21、Kester's Peter Biocca will present at the International Conference on Lead-free Soldering in Toronto, Ontario, Canada. ─── 凯斯特公司的Peter Biocca将出席在加拿大安大略省多伦多市召开的有关无铅焊接的国际会议。

22、Ideal for a variety of light duty applications including - laser fume extraction, soldering, dust collection, engraving, drilling, grinding. ─── 适合各种应用，包括-激光排烟，焊接，集尘，雕刻，钻孔，磨削。

23、The main products: silk screen machines, Dianjiao Ji, Mounter, reflow, wave soldering SMT-related tools and supplies. ─── 公司主要经营：丝印机、点胶机、贴片机、回流焊、波峰焊及SMT相关工具耗材。

24、Bare laminate, copper, solder resist or other surface. ─── 光面基材，覆铜板，绿油之或其它表面。

25、Separation of the component lead from the solder fillet. ─── 元件面或焊锡面的零件脚旁焊锡裂开。

26、Be sure to apply soldering within one month after opening. ─── ·请在开封后1个月内进行使用、安装。

27、For WCA have you accounted for changes in resistance due to tolerance, aging, temperature, soldering, etc.? ─── 在最坏情况分析中，电阻的精度应该如何考虑？

28、A better choice may be to evaluate and find a flux designed for lead-free since the lead-free fluxes almost always work for tin-lead soldering. ─── 一个更好的选择就是评选并找出一种适用于无铅的焊剂,因为无铅焊剂对于锡-铅焊接几乎总是有效的。

29、Low voltage 24V of both absorb gun and soldering pen has good protection of circuit board. ─── 吸锡枪及烙铁为低压输出24V及防静电设计,有效保护线路板。

30、Don't weld the battery with flat soldering because soldering melts battery insulator and damages safety circuit. ─── 不能直接用烙铁焊接电池，因为焊接时会融掉电池的绝缘体及损坏安全电路。

31、You might have to whip out a soldering item and deal with some bad connections. ─── 这时你可能需要一些焊接项目，修复那些坏死的线路连接。

32、The right choice of the most suitabele soldering paste is essential for an ideal and stable soldering result. ─── 为了要达到理想又稳定的焊锡效果，选择合适的锡膏是决定性的因素。

33、To make a solar panel, several modules have to be connected together. Then they apply a soldering flux on each module. ─── 为了做成太阳能电池板，几个模块必须连接在一起。然后，在每个模块采用焊接技术。

34、You might have to whip out a soldering item and deal with some bad connections. ─── 你可能需要一些焊接项目，修复那些坏死的线路连接。

35、What are the patent issues with using lead-free solder? ─── 使用无铅焊料涉及的专利问题有哪些?

36、Nitrogen use will however, reduce oxidation, enabling the use of less active fluxes and lesser quantities of flux for adequate soldering. ─── 尽管如此,使用氮气可以降低氧化,并允许使用活性较低的助焊剂,并降低正常焊接使用的焊剂量。

37、Dual function of soldering and hot air desoldering which have double performance. ─── 双功能结构,具备烙铁焊接和热风拆焊功能,使用效能双倍。

38、The amount of phosphorous deposited with the nickel determines whether the soldering is going to be reliable or not. ─── 随镍沉积的磷的含量决定焊接是否可靠。

39、Generally the same fluxes will work for lead-free solder. ─── 一般来说,相同的焊剂用于无铅焊料是有效的。

40、BGA measurement is measured for inside solder point. ─── BGA量测以最内侧焊点为量测依据。

41、or soldering those would take several lifetimes. ─── 焊接和连接这些晶体管需要好几辈子。

42、Do not solder directly to cells or batteries. ─── 不要直接对电池进行焊接。

43、When installing solder end valves, conventional soldering techniques should be used. ─── 安装焊接连接端口的阀门时，应该采用普通焊接技术。

44、Solder side is chosen to measure. ─── 4量测以吃锡面为选择点。

45、Care must be exercised in attaching the lead wires to the soldering tabs. ─── 在往焊接接线片上焊导线时必须非常小心。

46、What are the main qualification tests for using lead-free solder paste? ─── 使用无铅焊锡膏的主要评选测试有哪些?

47、What is a good method for solder bar addition for lead-free solder bar? ─── 如何才能很好的为无铅焊料棒添加焊料棒?

48、Blowtorch: a portable burner for mixing gas and oxygen to produce a very hot flame, used for soldering, welding, and glass blowing. ─── 喷灯：使混合气体和氧气产生更炽热火焰的便携助燃剂，常用于接合、焊接和玻璃吹制。

49、Remove indicator knob prior to soldering. Replace after soldering is completed. ─── 在焊接之前,拆卸指示器按钮。在焊接完成后,重新防止安装指示器按钮。

50、Hands-on experience PCBA soldering and debug as first plus. ─── 具备实际操作PCBA手工焊接和电路诊断经验，为首要优先条件。

51、Wrot copper performs well in high temperature applications and is easily joined by soldering or brazing. Wrot coper is exclusively used for fittings. ─── 在高温环境下,铜也表现很好,而且易于通过焊接或钎焊进行连接。铜专门用作配件材料。

52、Huizhou Taiyuan Metals Soldering Tin Products Co., Ltd. ─── 惠州市泰源五金焊锡制品有限公司。

53、When palladium is heated to gold soldering temperatures, no surface discoloration occurs... ─── 当钯加热到金的焊接温度时，表面不出现变色。

54、In soldering, the flux removes oxide films, promotes wetting, and prevents reoxidation of the surfaces during heating. ─── 在焊接时，熔剂用来除掉氧化皮，提高浸润性，防止加热时表面再氧化。

55、According each product, make and optimize profile，ensure mainboard soldering quality. ─── 制作产品的温度线：根据每个产品主板器件的分布，设定温度曲线，确保焊接质量。

56、A portable burner for mixing gas and oxygen to produce a very hot flame, used for soldering, welding, and glass blowing. ─── 喷灯使混合气体和氧气产生更炽热火焰的便携助燃剂，常用于接合、焊接和玻璃吹制

57、In the course of the lead free reflow soldering,lead and Lead free of reflow soldering affect the quality of product. ─── 在再流焊无铅化过程中,再流焊的有铅要素与无铅要素的兼容性直接影响产品质量。

58、Kester K100LD provides the lowest delivered price to the global wave soldering market. ─── 凯斯特K100LD在全球波峰焊接市场上的销售价格最低。

59、Overall design of soldering and SMD/BGA desoldering function. ─── 全面性维修设计,包括焊接及SMD/BGA拆焊双功能。

60、The machine motions like wire cutting, wire stripping and soldering will be adjusted and matched automatically. ─── 切断电线,剥皮,沾锡等动作各相关时间动作会自动搭配调整。

61、Forced convection cooling system to easily reach the requirements of strict lead free soldering processes. ─── 强制冷却系统实现急冷达到无铅焊接工艺的冷却降温要求。

62、And it can make full soldering on any parts and boards by applying adjusted design on the height of spout. ─── 喷口采可调式设计，对任何零件机板，均能作“完全锡焊”。

63、In SMT reflow soldering process,profiling a PCBA is a extremely important step. ─── 在SMT回流焊的整个流程中，为组装电路板设定合适的温度分布曲线是十分重要的一个环节。

64、When soldering to a gold plated surface the thickness of the gold is important. ─── 在焊接到镀金表面时,镀金层的厚度是非常重要的。

65、Type of high density solder mask. ─── 一种高密度焊料掩膜。

66、Reflow solder paste in 2 hours as soon as possible after printing. ─── 印刷后要在2小时内回流焊膏。

67、After reflow soldering and restored at room temperature, they meet the characteristics listed below. ─── 經過回流焊並冷卻至室溫後，電容器的特性符合下表的要求。

68、Development of advanced electronic package devices promoted the study on the reflow soldering. ─── 先进电子封装器件的出现推动了再流焊方法和设备的研究。

69、Again, you ll have to do some cable splicing and soldering, but in the end you avoid having to use an additional wall outlet. ─── 同样,也需要焊接一点儿电路,但是这样最后就不需要使用另外一个墙上的插座了。

70、to find out at this point than after you start soldering. ─── 这时检查，要比开焊之后才发现靠谱。

71、Use plenty of soldering flux to ensure a perfect connection. ─── 使用大量的焊接通量，以确保完美的连接。

72、In Lead-free wave soldering the Cu, Fe and Pb concentrations need to be followed very closely. ─── 在无铅波峰焊接中,需要严格遵循铜、铁和铅的浓度。

73、Used with the solder wire together, soldering a stainless steel etc metal. ─── 同锡线一起使用，焊接不锈钢等难以上锡的金属。

74、Maintenance the Wave soldering(WS) machine to ensure the maximum capability and efficiency. Trouble shooting. ─── 即时修护波峰焊机器产生之问题，维持波峰焊最佳之产能与效率。

75、It can make fuqq soldering on any parts and boards by applying adjusted design on the height of spout. ─── 喷口高低采可调式设计，对任何零件机板，均能作“完全锡焊”。

76、Overall functional design of 809 absorb gun and 907 antistatic soldering pen function. ─── 全面性维修设计,包括809电动真空吸锡枪及907防静电烙铁的全新双功能组合。

77、Both low voltage 24V soldering pen and absorb gun are antistatic design which has good protection of circuit board. ─── 吸锡枪及24V低压烙铁输出为防静电设计,有效保护线路板。

78、New dual function tweezers and soldering pen combination. ─── 全新电热镊子及烙铁双功能。

79、Be careful with that soldering iron; the business end is very hot. ─── 当心那烙铁，那一头很烫。

80、Good training program in hand soldering and periodic operator evaluation is conducted. ─── 对手焊锡工人有良好的培训计画,并定期对工人作技术考核及评估.

81、If too much solder is use, it may flow past tube and clog seating area. ─── 如果采用太多的焊料，则焊料可能流过管道并阻塞密封区域。

82、Single plated nickel barrier terminations has excellent solder heat resistance for soldering. ─── 外部电极为镍的电镀构造,于焊接时具有极优越的耐热性.

83、So disconnect the bench top power supply from circuit under test before soldering sensitive device. ─── 因此，在给敏感设备焊锡之前，必须将台式电源与测试电路断开.

84、When hand soldering, apply the soldering iron to the printed circuit board only. ─── 当用手焊时,只适用于焊在印刷电路板上。

85、The amount of refund tax should be consult with the solder . ─── 买单公司的退税金额应该和卖单企业商议。

86、All electronics assemblies using lead in solder. ─── 使用含铅焊料的所有电子配件。

87、So it will result in rigidity skin &block and solder balls etc. ─── 产生的后果是：锡膏出现硬皮、硬块、难熔并产生大量锡球等。

88、Be careful with that soldering iron. ─── 当心那烙铁。

89、Surface to solder are gold and clean. ─── 待焊接的表面是清洁的金面。